INSPECTION

-

 

INSPECTION

 

 

Inspection gives the measurement of the quality of the product or its utility in terms of the prescribed standards .in tool making the quality of each part of tool is reflected on the quality of the component .the quality must be specified in terms of strength, surface texture and dimensional accuracy.

 

  Inspection of the core & cavity should be thoroughly done after the final machining because any slight dimensional variations will affect the accuracy of the product.

 

OBJECTIVES OF THE INSPECTION:

1)    Inspection traces defects in raw materials and flows in process.

2)    It reduces further work on semi finished items thereby avoiding further wastage of time & recovery.

3)    It improves the quality of the product.

 

TYPES OF INSPECTION:

1)FLOOR INSPECTION :

Inspection taking place in the shop floor while the work is under progress on the machines .

 

2) CENTRALIZED INSPECTION:

          This kind of inspection is carried in a separate room where high accuracy measuring and comparing devices are available all the items are brought here only for inspection .the above two types are incorporated for this tool

 

Normally in inspection we used measuring instruments like:

 

1)    Vernier

2)    Micrometer

3)    Bore dial gauge

4)    Dials

5)    Trimos

6)    Profile projector

 

Comments

Post a Comment

Popular posts from this blog

Chemical test for Tragacanth

-
Chemical test for Tragacanth Organoleptic test: Appearance: Crystalline                                                          tragacanth Colour: White or faint yellow                                                 tragacanth Odour: None                                                                           tragacanth Taste: Mucilaginous                                                                tragacanth Solubility: Insoluble in alcohol, partially soluble in water      tragacanth Chemical test: SI.No. Test Observation Inference 1. To 4ml of 0.5%w/v solution add  0.5ml of HCl and heat for 30minutes on water bath Divide the hydrolyzed product in 2 parts a)       1 st part=Add 1.5ml of NaOH solution to neutralize and add Fehling’s solution A and B in equal quantities(mixed before) and warm over water bath. b)       2 nd part= Add barium chloride solution Red ppt o
Read more

MINOR DISORDERS OF NEW BORN AND ITS MANAGEMENT - NURSING ASSIGNMENT

-
INTRODUCTION         Neonatal health problems are frequently found ranging from minor physical or physiological peculiarities to the serious life threatening illnesses. Minor problems should not be ignored lightly without adequate assessment of the conditions. Early diagnosis and management of the serious problems help to overcome life long disability and to reduce neonatal morbidity and mortality. Nurses are responsible to manage the minor problems and to detect the serious problems for early and prompt management along with appropriate nursing interventions and support to the mother. MINOR DISORDERS OF NEW BORN 1. VOMITING         Vomiting is one of the common manifestations in the neonates. Regurgitation after feeds should not be confused with vomiting. Mucus vomiting often hinged with blood is quite common soon after birth. It is due to irritation often gastric mucosa by the swallowed materials during birth. Causes: ·         Dietic ·         Over feeding
Read more

KANGAROO CARE - NURSING ASSIGNMENT

-
INTRODUCTION         Caring low birth weight baby is a great challenge for the neonatal care unit and the family. Number of low birth weighs baby is still for beyond the expected target in our country. The cost of the quality management of these babies is increasing day by day. Kangaroo care is low cost approach for the care of low birth weight baby. This method of care was introduced and popularized by Dr.Edger Ray, Dr.Martinez and Dr.Charpak in late 1970s. DEFINITION         Kangaroo Mother Care (KMC) is a special way of caring low birth weight infants by skin to skin contact if promotes their health and welling by effective thermal control, breast feeding and bonding. KMC is initiated in hospital and continued at home. COMPONENTS OF KMC         In KMC, the infant is continuously kept in skin contact by the mother and breastfed exclusively to the utmost extent.         The two components of KMC are; 1.    Skin to skin contact is provi
Read more